edite print and fix your printer: Canon MP287 with error code E08

Canon MP287 with error code E08

This error appears with this message: “The Ink Absorber is Almost Full”

To solve this problem, you have to reset the waste ink counter.

Solution:

Turn on the printer.
The panel will display error E08, with message “The Ink Absorber is Almost Full”.
Download the Resetter for MP287
Printer must be in a state of Service Mode.
Turn off the E08 error by pressing the power button.
Do not unplug the power cord.
Press and Hold the button Stop/Reset followed by pressing the Power button.
Release the button Stop/Reset only.
Press the button Stop/Reset 6 times, then release both buttons simultaneously.
The printer MP287 will be in Service Mode.
LCD Panel will blank / dark and in your computer will detect new hardware. Ignore it.
Exctract and Run Service Tool for MP287
Click on “Play”, then the printer will proceed and will print one page with the words “D = 000.0″
Click “Clear EEPROM”. Then click “EEPROM”, and the printer will print the results Resetter. Writing one line as follows: “TPage (COPY TTL = 00 000 = 00 000)”.
Turn off by pressing the power.
Xerox Phaser 8560: Error Code 09,037.45

That's a ink loader error, due to the 8200 ink stick; to fix it:
Power down the printer.
Hold the back button and the info button at the same time, without letting go, power up the printer.
Keep holding down the buttons until the XEROX logo comes fully to the center of the screen, keep holding for 2 more seconds, then let go. I'll take about a minute or two for the Diagnostic screen to come up, the display will turn blank and black.
When the Diagnostic screen comes up go to down to the Function or Exercise option, there will be an option that says "clear ISC faults" it'll ask you to press OK to confirm, after you do then you will exit Diagnostics and the printer will reboot.
It should be fine until it happens again. Until all the 8200 ink is gone you will probably be doing this a few more times. Also make sure the 8200 ink is not jammed inside the ink loader, if it is then you have to un-jam it some how.

Printer Xerox Phaser 8560, 8560MFP

Download:

Drivers & manuals

Solid Ink:

108R00723: Solid Ink, Phaser 8560/8560MFP, Cyan (3 Sticks)
108R00724: Solid Ink, Phaser 8560/8560MFP, Magenta (3 Sticks)
108R00725: Solid Ink, Phaser 8560/8560MFP, Yellow (3 Sticks)
108R00726: Solid Ink, Phaser 8560/8560MFP, Black (3 Sticks)
108R00727: Solid Ink, Phaser 8560/8560MFP, Black (6 Sticks)
15 Pack Ink Set (6 Black, 3 Yellow, 3 Cyan, and 3 Magenta)

108R00675: Standard Capacity Maintanence Kit for Phaser 8500/8550
108R00676: Extended Capacity Maintanence Kit for Phaser 8550
109R00754: Waste Tray for Phaser 8500/8550 Series, 8560/8560

Parts:

097S03318: Printers CART W/STORAGE CAPACITY
097S03667: Duplex Module for Laser Printer
KTK6360/512: 512MB DRAM Memory Module
848k06552: Control panel

Troubleshooting:

Erreur 07,010.43:68691 : Printhead problem
Error 09,037.45
Control Panel Display is Blank

Check the Printer Power Sources and Isolate the Printer
Power the Printer OFF, Disconnect the Communication Cables, Wait 30 Seconds, and Then Power ON
Make Sure Control Panel is Properly Connected
Replace the Control Panel