jeudi 8 mars 2012

Fixing error E004 on canon IR1600

Fixing error E004 on canon IR1600



Solution:


Wiring
Is the connection of the connector (CN8) on the power supply PCB and the connector (J103) on the DC controller PCB and the wiring to the fixing assembly normal?
NO : Correct the connection and wiring.

Fixing assembly
Try replacing the fixing assembly.

Power supply PCB, DC controller PCB
Try repacking the power supply PCB. Is the fault corrected?
YES : End.
NO : Replace the DC controller PCB.

Error
With the power switch ON, clear E000 through E004; then, turn off and then on the power switch.

Fixing error E004 on canon IR1600

Fixing error E004 on canon IR1600



Solution:


Wiring
Is the connection of the connector (CN8) on the power supply PCB and the connector (J103) on the DC controller PCB and the wiring to the fixing assembly normal?
NO : Correct the connection and wiring.

Fixing assembly
Try replacing the fixing assembly.

Power supply PCB, DC controller PCB
Try repacking the power supply PCB. Is the fault corrected?
YES : End.
NO : Replace the DC controller PCB.

Error
With the power switch ON, clear E000 through E004; then, turn off and then on the power switch.

HP Photosmart B109, B109A, B109F, B109N Printers

Canon MX850 printer

Message "096: Fatal Error 02" with Oki printers

Message "096: Fatal Error 02" with Oki printers

096-02 error is a problem with the finisher.
That's a "tray raise or lowering error".

Solution 1:
  • Check and clean the upper limit switch. 

Solution 2:
  • Replace the upper limet switch

Solution 3:
  • Check the shift motor operation and finisher control PCB board. 
  • If the motor has failed, you need to replace it, and perhaps the control PCB too.

Error message Service Req E020 on Epson printers

Error message Service Req E020 on Epson printers


This error could appears on these models: EPL-N3000, Aculaser C1100, Aculaser C1900...


Solution 1: “Secondary transfer voltage contact/release problem”
  • Some electric parts can cause the trouble: 
  • Transfer Roller Pressure Solenoid (SL2) 
  • Transfer Roller Pressure Position Detection Sensor (PC7) 
  • Engine Board (PWB-A)  

Solution 2:
  • The problem come from the fuser. You have to replace it.
  • EPL-N3000: C13S053017BA 
  • Aculaser  C1100: 2090471
  • Aculaser C1900: 2077368

Error 61.05 on HP Designjet 500, 510, 800

Error 61.05 on HP Designjet 500, 510, 800

Could appears on HP DesignJets 800 Series, DesignJet 500 and 510.

Printer show a System Error: 61:05

The problem:

That's an error Processing Job.
This Error Code appears in these HP DesignJets with an HPGL/ 2 card installed, when processing either a PostScript or HP-GL/2 file.

Solution 1:
  • Switch the Printer Off 
  • Wait a few minutes. 
  • Switch the Printer On 
  • Resend the file that you were trying to print. 

Solution 2:
  • If the Error Code reappears, try to generate the file again and try to print again. 
  • If the file that is causing this error is PostScript, check if it is Binary. If the file is Binary, use AppleTalk to send the file to the Printer. 
  • If AppleTalk is not being used to send the Binary file to the Printer, you have to change the PostScript settings to Binary through the Front Panel (Set-up menu / PS settings / Encoding / Binary). 


Solution 3:

How to reset drum counter on Oki B4400

How to reset drum counter on Oki B4400


Solution to reset the drum counter:
  • Open the Status Monitor.
  • Click "Printer Setup" then "Open Configuration" and "Maintenance".
  • Click Drum Counter Reset. Click Apply.
  • Click OK


Réinitialiser le compteur du tambour
  • Ouvir le Status Monitor.
  • Cliquer sur "Printer Setup" puis "Open Configuration" et "Maintenance".
  • Cliquer sur Drum Counter Reset (Réinitialiser le compteur du tambour). Cliquer Apply (appliquer).
  • Cliquer sur OK

Cero el contador del cilindro


  • Abras Status Monitor.
  • Clic en "Printer Setup" y "Open Configuration" y "Maintenance".
  • Clic en Drum Counter Reset. Clic Apply (aplicar).
  • Clic OK

Reiniciar o contador do cilindro

  • Lance o Status Monitor.
  • Clique com "Printer Setup", "Open Configuration", "Maintenance".
  • Clique com Drum Counter Reset. Clique Apply (aplicar).
  • Clique OK

SSC Service Utility Software to reset Epson printers

SSC Service Utility Software to reset Epson printers

SSC Service Utility Software to reset Epson printers


SSC Service Utility allow to do many things with Epson printer :


- Work directly with CSIC in Epson Stylus printers cartridges.
- Reset or rewrite any chip using special addon device.
- Freeze internal ink counters.
- Reset internal ink counters even with empty cartridges.
- Separate cleaning of color and black heads for all Epson inkjet printers, powerful cleaning mode.
- Hot swapping of cartridges supported.
- Resetting of protection counter.
- More then 100 different Epson printers supported


The site: http://www.ssclg.com/epsone.shtml

Download the 4.30 version


Printers you can reset with SSC utility:

Epson Stylus Сolor 400/440/480 LPT/480SXU/580/600/640/660/670/680/777/740/760/ 800/850/860/880/900 / EM-900C/980/1160/1520/3000
C20 / C40 / CL-750/C41 / C42 / C43 / C44 / C45 / C46 / C47 / C48/C50/C60/C61
C62 /C63 / C64 /C65 / C66/C67 / C68 / D68/C70/C80/C82/C83 / C84/C85 / C86/C87
C88 / D88 and PE
Photo RX420 / RX425 / RX430 /RX500 / RX510/RX520/RX600 / RX610/RX620/RX700 CX3100 / CX3200/CX3500 / CX3600 / CX3650/CX3700/CX3800 / CX3810 / DX3800/CX4500 CX4600/CX4100 / CX4200 /CX4700 / CX4800/DX4200 / DX4800 /CX5100 / CX5200 /CX5300 / CX5400 CX6400 / CX6600 /CX6300 / CX6500 /CX7800 Photo /Photo EX /Photo 700 / IP-100/750 / PM-770C /780 / 790 /
PM-780C /810 / 820
Photo 820 /825 / 915/830 / 830U/870 / PM-875DC /R200 / R210/R220 / R230
R300 / R310 / Photo R320/R800 / PX-G900/R1800/R2400/890/PM-890C/PM-A700
PM-G720/PM-970C/895/ 785EPX
Photo 900 /925 / 935/ 950 / 960 / PM-950C/1200 / PM-3000C/1270 / PM-3300C/1280 / PM-3500C
Photo 1290/2000P/2100/2200 / PM-4000EPX/Pro 5000 / PM-5000C

 

Lexmark Genesis S800, S815 printer

Lexmark Genesis S800, S815 printer

Dowmnloads:

Cartridges:


Parts:

Troubleshooting:
  • Printhead errors: reinsert the printhead
- Open the front door of the printer, and then open the printhead access door.
- Pull the latch forward, and then remove the printhead.
- Wipe the printhead contacts using a clean, lint-free cloth.
- Reinsert the printhead, and then push the latch until it clicks into place.
- Close the printhead access door, and then close the front door.
- If the error persist, the printhead must be replaced.

Canon MP287 with error code E08


Canon MP287 with error code E08



This error appears with this message: “The Ink Absorber is Almost Full

To solve this problem, you have to reset the waste ink counter.

Solution:
  • Turn on the printer.
  • The panel will display error E08, with message “The Ink Absorber is Almost Full”. 
  • Download the Resetter for MP287 
  • Printer must be in a state of Service Mode. 
  • Turn off the E08 error by pressing the power button. 
  • Do not unplug the power cord. 
  • Press and Hold the button Stop/Reset followed by pressing the Power button. 
  • Release the button Stop/Reset only.
  • Press the button Stop/Reset 6 times, then release both buttons simultaneously.
  • The printer MP287 will be in Service Mode. 
  • LCD Panel will blank / dark and in your computer will detect new hardware. Ignore it. 
  • Exctract and Run Service Tool for MP287 
  • Click on “Play”, then the printer will proceed and will print one page with the words “D = 000.0″ 
  • Click “Clear EEPROM”. Then click “EEPROM”, and the printer will print the results Resetter. Writing one line as follows: “TPage (COPY TTL = 00 000 = 00 000)”. 
  • Turn off by pressing the power. 

  • Xerox Phaser 8560: Error Code 09,037.45


    That's a ink loader error, due to the 8200 ink stick; to fix it:

  • Power down the printer.
  • Hold the back button and the info button at the same time, without letting go, power up the printer.
  • Keep holding down the buttons until the XEROX logo comes fully to the center of the screen, keep holding for 2 more seconds, then let go. I'll take about a minute or two for the Diagnostic screen to come up, the display will turn blank and black.
  • When the Diagnostic screen comes up go to down to the Function or Exercise option, there will be an option that says "clear ISC faults" it'll ask you to press OK to confirm, after you do then you will exit Diagnostics and the printer will reboot.
  • It should be fine until it happens again. Until all the 8200 ink is gone you will probably be doing this a few more times. Also make sure the 8200 ink is not jammed inside the ink loader, if it is then you have to un-jam it some how. 

Printer Xerox Phaser 8560, 8560MFP


Download:
Solid Ink:
  • 108R00675: Standard Capacity Maintanence Kit for Phaser 8500/8550
  • 108R00676: Extended Capacity Maintanence Kit for Phaser 8550
  • 109R00754: Waste Tray for Phaser 8500/8550 Series, 8560/8560

Parts:

Troubleshooting:

  • Erreur 07,010.43:68691 : Printhead problem
  • Error 09,037.45
  • Control Panel Display is Blank

Oki B6300 Mono Laser printer

Downloads:

Toner:
  • 09004078: Toner/Drum Oki black 10000 sheets

Parts:

Troubleshooting: